Search
Close this search box.

How to Replace the Lawn Mower Pull Cord

How to Replace the Lawn Mower Pull Cord

Share This Post

To replace the lawn mower pull cord, remove the old cord, and thread the new one through the starter housing and handle. This process ensures smooth lawn mower operation without any interruption.

Maintaining the pull cord of a lawn mower is crucial for its whole functionality. Over time, the pull cord may become frayed or break, requiring replacement. By following a few simple steps, you can easily replace the lawn mower pull cord and get your machine running smoothly again.

How to Replace the Lawn Mower Pull Cord? We will guide you through the process of replacing the pull cord, ensuring that you can maintain a well-functioning lawn mower.

1. Assessing The Damage

Check the condition of the pull cord:

Before replacing the lawn mower pull cord, it’s essential to assess the damage and determine if the cord needs replacement or repair. Start by checking the whole condition of the pull cord. Look for any signs of wear, fraying, or breaking. If the cord is severely damaged or has completely snapped, it’s clear that you need a replacement. However, if the cord is slightly damaged or has minor issues, it might be possible to repair it.

Inspect the cord thoroughly from end to end, looking for any weak spots or areas that seem vulnerable. Make sure to check the handle as well, as it can also wear out over time. If the damage is limited to a small section of the cord, you may be able to cut off the affected part and reattach it to the handle.

Remember, safety should always be a priority, so if the cord is too severely damaged or you’re unsure about its condition, it’s better to replace it to avoid any potential accidents.

2. Gathering The Tools And Materials

To successfully replace the lawn mower pull cord, you will need the following tools:

Tools Materials
Socket wrench Replacement pull cord
Spark plug socket Penetrating oil
Needle-nose pliers Clean rag
Screwdriver (flathead or Phillips) Work gloves
Torque wrench Safety goggles

Make sure to gather all these tools and have the necessary materials at hand before starting the replacement process. Having everything ready will ensure a smooth and efficient cord replacement.

3. Removing The Old Pull Cord

Replacing the pull cord on your lawn mower is an important maintenance task that you may need to do at some point. One of the first steps in this process is removing the old pull cord. This can be done safely and efficiently by following a step-by-step guide.

First, prepare the necessary tools for the task, such as pliers and a replacement pull cord. Begin by locating the old pull cord and inspecting it for any signs of wear or damage. Then, use the pliers to carefully detach the cord from its housing. Take caution to avoid damaging any surrounding components.

Next, untie or unknot the old cord from the handle, making sure to keep track of the knotting technique. This will help when attaching the new pull cord later. Once the old cord is completely removed, check the roping mechanism and clean it if necessary.

By following these steps and exercising caution, you can safely remove the old pull cord from your lawn mower. Remember to always refer to the manufacturer’s instructions for specific guidance relating to your equipment.

4. Measuring And Cutting The Replacement Cord

To accurately measure and cut the replacement cord for your lawn mower pull, follow these steps:

  1. First, measure the length of the old cord and note it down.
  2. Next, uncoil the new cord fully and straighten it.
  3. Starting from one end, cut the cord to the same length as the old one.
  4. Make sure to use sharp scissors or a utility knife to achieve a clean cut.
  5. Double-check the length before trimming off any excess cord.
  6. Once you are confident about the length, use a lighter or heat gun to seal the cut end, preventing fraying.
  7. Now, you have a correctly measured and cut replacement cord for your lawn mower pull.

5. Preparing The Recoil Starter Assembly

Before inserting the new pull cord, it is important to properly prepare the recoil starter assembly. Here’s how to do it:

TaskSteps
Remove old cordUnscrew any screws or bolts holding the old pull cord in place.
Clean assemblyAfter removal, clean the recoil starter assembly with mild detergent and warm water to eliminate accumulated dirt.
Inspect componentsWhile cleaning, inspect components for damage or wear, such as frayed edges or broken springs.
Lubricate moving partsApply a small amount of lubricant to moving parts for smooth operation, reducing friction and extending component life.

By following these steps, you will have properly prepared the recoil starter assembly for the insertion of the new pull cord. Now you can proceed with the next steps in replacing the lawn mower pull cord.

6. Installing The New Pull Cord

Installing the new pull cord on your lawn mower is a simple process that can be done in just a few steps. Here’s a step-by-step guide to help you install the new cord properly:

  1. Remove the old pull cord by unscrewing the bolts that hold the pulley cover in place.
  2. Take the new pull cord and thread it through the hole in the pulley, ensuring that it is securely attached.
  3. Wind the cord around the pulley, making sure to keep tension on it as you go.
  4. Once the cord is wound around the pulley, thread it through the eyelet on the mower handle.
  5. Tie a knot at the end of the cord to secure it in place.
  6. Test the new pull cord by giving it a gentle tug to ensure that it is working properly.

By following these steps, you can easily replace the lawn mower pull cord and ensure that it is securely attached. Take your time and double-check your work to prevent any future issues.

7. Testing The Pull Cord

To ensure that the replacement of the pull cord on your lawn mower is successful, it is essential to perform a test run once the installation is complete. This test run will help in determining if everything is working properly and if any potential issues need to be addressed. To perform the test, follow these steps:

  1. Start by firmly gripping the pull cord handle and giving it a firm pull to start the lawn mower.
  2. Observe if the pull cord retracts smoothly after the initial pull.
  3. Listen for any unusual noises or vibrations coming from the lawn mower.
  4. Check if the engine starts easily and runs smoothly.
  5. Ensure that the lawn mower blades engage and rotate properly.

If any issues are observed during the test run, it is important to troubleshoot and address them immediately. This may involve checking the installation of the pull cord, inspecting the spark plug, cleaning the air filter, or adjusting the carburetor. By performing a thorough test run and troubleshooting any potential issues, you can ensure that your lawn mower is in proper working condition and ready for use.

8. Maintaining The Pull Cord

Maintaining the pull cord of your lawn mower is essential in ensuring its long-lasting use. Proper maintenance practices can help extend the lifespan of the cord. Here are a few tips to help you maintain the pull cord effectively:

TipsInstructions
Keep it cleanRegularly inspect the pull cord for dirt, debris, or grass clippings. Clean using a soft cloth.
Lubricate regularlyApply a small amount of outdoor equipment lubricant to the cord mechanism for smooth operation.
Avoid excessive forcePull the cord gently with steady pressure. Avoid yanking or jerking to prevent fraying or breaking.
Store properlyWhen not in use, store the lawn mower in a dry, sheltered area to maintain its longevity.

By following these maintenance tips, you can ensure that your lawn mower’s pull cord remains in good condition, allowing for easy and hassle-free starts every time.

9. Additional Tips And Safety Precautions

When replacing the pull cord of your lawn mower, there are a few additional tips and tricks that can make the process smoother and help you avoid potential safety hazards. Here are some important points to keep in mind:

  • Inspect the recoil starter assembly: Before replacing the pull cord, thoroughly inspect the entire recoil starter assembly to ensure it is in good condition. Look for any signs of damage or wear and tear, such as frayed cables or broken components.
  • Clean and lubricate: Take the time to clean any debris or dirt that may have accumulated around the recoil starter assembly. Also, lubricate the moving parts to ensure smooth and efficient operation.
  • Use the right cord material: When replacing the pull cord, choose a high-quality cord material that is specifically designed for outdoor use. This will ensure durability and longevity.
  • Properly tension the cord: When attaching the new pull cord, make sure it is properly tensioned. An overly loose or tight cord can affect the starting mechanism and lead to issues.
  • Wear protective gear: Always wear appropriate protective gear, such as gloves and safety glasses, to protect yourself from any potential accidents or injuries.
  • Consult the manufacturer’s manual: It’s essential to consult the manufacturer’s manual for specific instructions and safety precautions related to your lawn mower model. Follow the guidelines provided to ensure a successful replacement process.

Frequently Asked Questions For How To Replace The Lawn Mower Pull Cord

How Do You Replace A Pull Cord On A Lawnmower?

To replace a pull cord on a lawnmower, follow these steps: 1. Remove the housing covering the cord. 2. Unwind and remove the old cord. 3. Install the new cord by threading it through the recoil pulley and securing it with a knot.

4. Wind up the recoil pulley to tension the cord. 5. Replace the housing. Done!

How Do You Fix A Lawn Boy Pull Cord?

To fix a Lawn Boy pull cord, follow these steps: 1. Remove the engine cover. 2. Locate the recoil starter assembly. 3. Inspect the rope for fraying or breaks. 4. Replace the rope if needed. 5. Reassemble the engine cover. Remember to use proper safety precautions and consult the Lawn Boy manual for specific instructions.

How Do You Fix A Pull Cord Spring On A Lawn Mower?

To fix a pull cord spring on a lawn mower, start by removing the spark plug wire. Then, take off the starter cover and locate the broken spring. Replace the spring with a new one of the same size, making sure it is properly wound.

At the very end, reassemble the starter cover and reconnect the spark plug wire.

How Do You Fix A Stuck Pull Cord On A Lawn Mower?

To fix a stuck pull cord on a lawn mower, start by removing the engine cover. Check if the cord is tangled or damaged, and if so, replace it. If not, ensure the recoil spring is functioning properly and lubricate the parts if needed.

Reinstall the cover and test the pull cord.

Conclusion

To wrap up, replacing the lawn mower pull cord doesn’t have to be a daunting task. By following the step-by-step instructions mentioned in this blog post, you can easily get your lawn mower up and running again. Remember to take proper safety precautions, gather the necessary tools, and follow each step with care.

With a little patience and effort, you’ll have a functioning pull cord in no time. Happy mowing!

Spread the love

More To Explore

Leave a Comment